Dear,
How can I210 work under windows 2003 as I210 no support this OS? Thanks.
↧
Intel i210 driver for Windows 2003
↧
Indoor Positioning
Hi, just want to ask is NRF24L01 compatible with Intel Galileo Gen 2 board? Do anyone have any tutorial that I can refer to? Thanks
↧
↧
Intel 82579V Issue
<><> Apologies if this has been posted in the wrong place <><>
Ok I'll keep this brief.
Problem:- LAN regulary disconnects and reconnets 30 seconds later.
Symptons:- Loose connection to Lan / Internet for around 30 seconds.
Background:- Had this problem with both P8P67 B2 and P8P67 pro boards. I have several other computers connected to the switch (not hub) and they are working fine. Have replaced the lead to no avail. Have even used the same lead in several other computers which works fine.
Config:-
Study
Netgear 8 port SWITCH 10/100/1000
Server
VOIP
PC
Switch connected to lounge hard wired via outdoor sheilded cat6 lead.
Lounge
Netgear 8 port SWITCH 10/100/1000
Router
XBOX 360
Wii
<><><>
Message in System Event Logs;-
<><>
Warning message - date time - source = e1cexpress
Event ID = 27
Intel 82579V Gigabit Network Connection
- Network link is disconnected
<><>
Then it states its connected again.
Have also tried the following;-
Remove Kaspersky 2011
Ensure ALL power management even OS is disabled
Use IPV4 instead of IPv6 in prefix policies
Disable nativue IPv6
Disable tunnel IPv6
Disable IPv6
netsh interface tcp set global rss=disabled
netsh interface tcp set global autotuninglevel=disabled
netsh int ip set global taskoffload=disabled
Disabled SNP;-
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\Tcpip\Parameters]
EnableTCPChimney=dword:00000000
EnableTCPA=dword:00000000
EnableRSS=dword:00000000
Have tried driver from Asus MB CD, Asus Website, Your Website, Windows Update all to no avail.
Please help.
↧
Modify open source linux driver
Hello,
I am interested in using an intel 10GB network card to move data directly
to and from another PCIe card. This other card supports DMA transfer through a
simple API in its driver.
Can anyone advise me on the best way of doing this? I have not
done any linux driver development before, but I have a lot of programming experience
in C.
Thanks,
Aaron
↧
"No probed ethernet devices" when use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1
I encountered error message "No probed ethernet devices" when I tried to use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1 environment (OS: CentOS 7, Server: DELL PowerErge R720).
Can anyone tell me how to use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1 ?
↧
↧
Keeping network settings after driver update?
Afternoon
Using proWin32.exe downloaded from the intel site, I can update the network drivers on my machine(s)
However, when I do this both the network settings and the VLAN (I use Vlan taging at the local machine) are lost.
This means updating the drivers remotely is not possible....since as soon as the drivers are updated, the machine
drops off the network
Does anyone know of a way to persist the network config post-update, without having to visit each machine in turn...?
↧
ac 7260 at 7 meters 0 download speed.
hi all i finally comprobed ac 7260 is a shitof adaptor. i just buy yesterday a p55w toshiba and in my room no conection or very slowrate where my 8 years old pc never had problems. now i recognize i have to stay 4 max 5 meter arround the router in order to have some internet. so........ intel take you modern techonlogy and trash it. now i will giveback the computer and i will say all peple i know intel wifi is adisaster. you deserver your company fail up. incompetence from one multimilionaire company is unaceptable. 8 yearsof technology avences and thisis the resoult. is ashame, for people who know what shame is.....
↧
Intel I340-T4
Hello, seeking help with this 2 port pci-e nic. I am trying to build a home vmware lab to study for vcp 5.5 and was hoping to use this card in a system (tower) i built, specs below. the card can not be recognized (pnp) by 2008 r2 or 2012 r1. Unfortunaltely their are no led lights in the front plate for this card. When installing the prowinx64 driver, it will quit and say the software could not install since there are no nic card detected.
I have switched the nic from one pci-e slot to another, but same result. I have tried to different computers to make sure the nic is not faulty. From what I can tell, the bios only allows me to disable the internal nic. Any help would be appreciated.
Biostar Ta970 MB
Internal Realtek RTL8111F - 10/100/1000 Controller
AMD FX-6300
↧
Nothing but problems with Intel pro 1000 mt, teaming, etc
[rant on]
First off the Intel drivers are the dumbest thing I can imagine. They won't upgrade, they won't uninstall the old junk and they won't work. Yes, it's a 10yr old machine and the drivers stopped being able to be upgraded 5 yrs ago and it's been a PITA ever since Intel screwed up these drivers.
Long story short, it's been about 5 years I've been hacking at this junk from time to time. It used to be two mirrored servers that worked great, at one point I attacked the main server's nic driver problem and fouled it up so badly it never ran again. After much hacking the secondary machine became the primary and only and it's NEVER had teaming working again. Single nic, mediocre performance.
I've got a new server (thankfully without an Intel Nic) that's running great, but it's time the old dog got some work and get this stupid driver fixed.
FINALLY, today I find where I can MSIZAP the old trash out. Install the latest drivers.
Team this crap together and what the freak do you know but teaming fails?
Team the adaptors together and set the static ip and darned if the stupid thing says 'access to local only'
AGGGGGGGG.
Delete the team and it's still FUBAR
I cannot believe that these intel drivers have gotten this bad. Used to be they were super, but now they suck and are increably hard to get configured.
Anyway, rant over.
System is a win server 2008 32 bit with two INTEL Pro/1000 MT dual port nics.
Windoze is up to date, upgraded from 2003 which had the same freeking problem.
Only way I can get it to connect is to enable DHCP, which of course defeats the purpose of having a !SERVER! in the first place.
I'm ready to push thing thing out into the swimming pool at this point.
I cannot freekin believe how bad this problem has been to resolve...uhhhh, not resolve that is.
GRRRRR.
Any assistance would be greatly appreciated. Thanks in advance. {sorry for the rant, but seriously Intel, why so freekin bollixed up?}
↧
↧
i218-LM code 10 after restart without cable
I have a system using an Intel i218-LM ethernet controller:
- Fully patched (as of 16th Feb 2015) Windows 8.1 64-bit
- Intel driver PROWinx64.exe, Version:19.5, Date:28th Oct 2014. Appears in Windows as driver v12.12.80.19 dated 29th Sept 2014.
Under normal operation the LAN works correctly. I can disconnect and re-connect the LAN cable, and each time the LAN connection is re-established.
If I perform a system restart with the LAN cable connected, the LAN is established correctly once Windows boots.
However, if I perform a system restart without a LAN cable connected then I get a Code-10 error in Windows under Device-Manager for the i218-LM controller. When I re-connect the LAN cable obviously the connection isn't re-established due to the Code-10 error. If within Device-Manager I disable and then re-enable the i218-LM, the Code-10 error goes away, and the connection is correctly established.
Any ideas?
↧
Intel Boot Agent ??
I had a virus.
I restored a backup computer D845PESV Windows XP Pro SP3.
My old backup was not my new PCI Ethernet card Intel PRO / 1000Mbps PCI ACPI, Wake on LAN, PXE.
She has been recognized and works very well.
I am still a problem at every boot I have ever had before, a DOS window that says:
Initialyze and etablishing link
Intel Boot Agent GE v1.2.22 DHCP
PXE-E53 No boot file
PXE-MOF Exiting boot
How to remove this procedure?
Thank you for your cooperation
↧
Remote Booting Z800
Hello,
I have a series of Z800 workstations working as a render farm.
Occasionally, for a variety of reasons, I need to boot them from off- not just sleep or hibernate- but completely shutoff from a remote location.
They all have the same processors: dual Xeon X5660
I've read that the z800s are AMT enabled however, when I boot one (locally) and get into the BIOS, there are no options regarding Intel AMT.
They also have broadcom netextreme nics that also supposedly support remote booting from completely off but I'm lost on how to get something like that going.
Can anyone point me in the right direction? Is there a piece of software I'm missing? Some driver I need to update?
It would be a huge time saver and fantastic if I could remote boot- whether it's using the NIC, AMT, or whatever works!
Thanks!
-Stephen
↧
82579V in vlan not respond to requests
Hello,
I'ma problemwithmynetwork card(82579V) has createdthreeVLANs(20/10/30) and does not respondto anyrequest forany computerwithin theseVLANs.
Haveupdated thedriverand thissame,I can doto solve the situation?
Sorry my english
Thanks
Tiago
↧
↧
I work on intel WG 82583 and I have problem to program falsh memory
I work on WG 82583. When I install the drivers the PC detects a intel 82574 and an error code 10 appears on the device manager.
In my flash of the 82583, I have nothing.
What is the procedure to update an image on flash ?
!
↧
Intel(R) 82562V 10/100 Network Connection
Hi, I've recently pulled out an old computer to upgrade it (HP Pavilion a1640n) and I cannot seem to find any working drivers for the Intel(R) 82562V 10/100 Network Connection. I have tried searching through various forums, driver bases, etc. but cannot seem to get this to work. In addition the driver update posted here: Intel® Download Center does not fix the problem or change anything. Wondering if anyone can help me out.
Thanks,
John S.
↧
Unable to establish link with Intel 82599ES 10-Gigabit SFI/SFP+ Network Connection
Hi,
I'm looking for help establishing (and troubleshooting) a link to a SPAN in promiscuous mode on Ubuntu Server 14.04.
This link was up and running and seeing packets for a few weeks. To help with an application issue, we installed the PF_RING kernel module, and after a server reboot, we have not been able to establish a link. We've rolled back our changes and removed PF_RING, but we are still not able to establish a link, and I'm looking for some help.
We've looked at our Gigamon SPAN and it appears to be sending data to our device but we have not been able to see any traffic ('tcpdump -i em1 -vv' does not see any traffic).
Any help would be greatly appreciated.
Jeff
$ifconfig em1
em1 Link encap:Ethernet HWaddr ec:f4:bb:**:**:**
UP BROADCAST NOARP PROMISC MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:7180 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
$ sudo ethtool em1
Settings for em1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
10000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: FIBRE
PHYAD: 0
Transceiver: external
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: no
$ cat /var/log/syslog | grep ixgbe
Feb 17 15:16:46 servername kernel: [ 7.371724] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.15.1-k
Feb 17 15:16:46 servername kernel: [ 7.371727] ixgbe: Copyright (c) 1999-2013 Intel Corporation.
$ cat /var/log/syslog | grep em1
Feb 17 15:16:46 servername kernel: [ 11.789614] systemd-udevd[572]: renamed network interface eth0 to em1
Feb 17 15:16:46 servername kernel: [ 14.071614] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
Feb 17 15:16:46 servername kernel: [ 15.404429] ixgbe 0000:01:00.0: registered PHC device on em1
Feb 17 15:16:46 servername kernel: [ 15.509280] IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
Feb 17 15:16:47 servername kernel: [ 15.580413] ixgbe 0000:01:00.0 em1: detected SFP+: 6
Feb 17 15:16:48 servername kernel: [ 16.713425] device em1 entered promiscuous mode
Feb 17 15:16:48 servername kernel: [ 17.498677] ixgbe 0000:01:00.0 em1: detected SFP+: 6
$sudo ethtool -m em1
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x10 0x00 0x00 0x01 0x00 0x00 0x00 0x00
Transceiver type : 10G Ethernet: 10G Base-SR
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x06 (64B/66B)
BR, Nominal : 10300MBd
Rate identifier : 0x02 (8/4/2G Rx Rate_Select only)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 80m
Length (62.5um) : 30m
Length (Copper) : 0m
Length (OM3) : 300m
Laser wavelength : 850nm
Vendor name : Intel Corp
Vendor OUI : 00:1b:21
Vendor PN : FTLX8571D3BCV-IT
Vendor rev : A
Optical diagnostics support : Yes
Laser bias current : 26.446 mA
Laser output power : 0.6639 mW / -1.78 dBm
Receiver signal average optical power : 0.0014 mW / -28.54 dBm
Module temperature : 51.65 degrees C / 124.97 degrees F
Module voltage : 3.3214 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : On
Laser rx power high warning : Off
Laser rx power low warning : On
Laser bias current high alarm threshold : 11.800 mA
Laser bias current low alarm threshold : 2.000 mA
Laser bias current high warning threshold : 10.800 mA
Laser bias current low warning threshold : 3.000 mA
Laser output power high alarm threshold : 0.8318 mW / -0.80 dBm
Laser output power low alarm threshold : 0.1585 mW / -8.00 dBm
Laser output power high warning threshold : 0.6607 mW / -1.80 dBm
Laser output power low warning threshold : 0.1995 mW / -7.00 dBm
Module temperature high alarm threshold : 78.00 degrees C / 172.40 degrees F
Module temperature low alarm threshold : -13.00 degrees C / 8.60 degrees F
Module temperature high warning threshold : 73.00 degrees C / 163.40 degrees F
Module temperature low warning threshold : -8.00 degrees C / 17.60 degrees F
Module voltage high alarm threshold : 3.7000 V
Module voltage low alarm threshold : 2.9000 V
Module voltage high warning threshold : 3.6000 V
Module voltage low warning threshold : 3.0000 V
Laser rx power high alarm threshold : 1.0000 mW / 0.00 dBm
Laser rx power low alarm threshold : 0.0100 mW / -20.00 dBm
Laser rx power high warning threshold : 0.7943 mW / -1.00 dBm
Laser rx power low warning threshold : 0.0158 mW / -18.01 dBm
↧
Intel Pro 1000 PT Quad Port will not install Intel Pro 1000 PT Quad Port drivers
I swear, nothing but problems with Intel drivers these days.
Picked up a quad port Pro 1000 PT.
Installed it.
Can't install the Intel drivers so I can team it.
This is the dumbest stuff I've seen in a long time.
WTF do I have to do to get these Intel Nics to work these days?????
↧
↧
XL710 QSFP NICs: will a 4xSPF breakout give me 4 ethernet ports?
I have a very basic question concerning the new XL710 QSFP NICs (i.e., XL710QDA1/2). Will a QSFP to 4xSPF breakout give me 4 ethernet ports or are these NICs only intended to be connected to switches.
TIA.
John Treble
Ottawa, Canada
↧
Modify open source linux driver
Hello,
I am interested in using an intel 10GB network card to move data directly
to and from another PCIe card. This other card supports DMA transfer through a
simple API in its driver.
Can anyone advise me on the best way of doing this? I have not
done any linux driver development before, but I have a lot of programming experience
in C.
Thanks,
Aaron
↧
"No probed ethernet devices" when use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1
I encountered error message "No probed ethernet devices" when I tried to use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1 environment (OS: CentOS 7, Server: DELL PowerErge R720).
Can anyone tell me how to use Intel Ethernet Server Bypass Adapter X520-SR2 in DPDK 1.7.1 ?
↧